TX-SR3100 - Initial Setup with Auto Start-up Wizard
Operations
When you turn the unit on for the first time after purchase, the Initial Setup
screen is automatically displayed on the TV to allow you to make settings
required for startup using simple operations following on-screen guidance.
1. Switch the input of the TV to the input connected to the unit.
2. Put batteries into the remote controller of this unit.
3. Press ON/STANDBY on the remote controller to turn the unit on.
4. When the language selection screen is displayed on TV, select the language
with the cursors ^/v UP/DOWN and press ENTER.
- Select the item with the cursors of the remote controller, and press ENTER to
confirm your selection. To return to the previous screen, press RETURN/
EXIT. - If you have terminated the Initial Setup halfway, turn this unit to standby mode
and turn the power on again. Then you can display the Initial Setup again.
The Initial Setup appears on the screen each time the power is turned on
unless the Initial Set up is completed or "Never Show Again" is selected on
the first screen. - To perform the Initial Setup again after the setting is completed, press
SETUP, select "Miscellaneous" - "Initial Setup", and press ENTER.
Speaker Setup
1. Select the connected speaker configuration and press ENTER.
Note that the image on the screen changes each time you select the number
of channels in "Speaker Channels".
2. The speaker combination selected in step 1 is displayed. "Yes" is displayed
for the selected speakers. If the setting is correct, press ENTER.
3. Select "Next" and press ENTER. Then a test tone is output from each
speaker to confirm the connection. Selecting each speaker with the cursors
^/v UP/DOWN will output the test tone. Press ENTER after confirmation.
4. If there is no problem with the speaker connection, select "Next" and press
ENTER. To return to "Speaker Setup", select "Back to Speaker Setup" and
press ENTER.
ARC Setup
If you have connected a TV that supports ARC, select "Yes" and press ENTER.
AccuEQ Room Calibration
Place the supplied speaker setup microphone at the listening position. The unit
automatically measures the test tones output from each speaker, and sets the
optimum volume level for each speaker, the crossover frequencies, and the
distance from the listening position. This also reduces the effect of the standing
wave in accordance with the viewing environment and automatically adjusts the
equalizers for the speakers, and enables correction of sound distortion caused
by the acoustic environment of the room.
- It takes between 3 and 12 minutes for calibration to be completed.
- If you connect a subwoofer, check the power and volume of the subwoofer.
Set the subwoofer volume to more than half. - If the power of this unit suddenly turns off, the wires in the speaker cables
have touched the rear panel or other wires, and the protection circuit is
working. Twist the wires again securely, and make sure they do not stick out
of the speaker terminals when connecting.
1. Connect the supplied speaker setup microphone to the SETUP MIC jack on
the main unit.
When placing the speaker setup microphone on a tripod, refer to the
illustration.
2. Confirm a test tone is output from the subwoofer and press ENTER.
3. Press ENTER to output test tones from each speaker, and the connected
speakers and the noise in the surrounding environment are automatically
measured.
4. The measurement results in step 3 are displayed. If there is no problem in
the detection result of the speaker, select "Next" and press ENTER to output
the test tone again to automatically set the settings such as volume level,
crossover frequency, etc., to their optimum. (The test tone is automatically
output when 10 seconds has elapsed without any operation.)
- When an error message is displayed or when the connected speakers
cannot be detected, perform re-measurement by selecting "Retry" and
pressing ENTER. - When it cannot be resolved by performing the re-measurement, confirm
if the speakers are connected correctly. If there is any problem with the
speaker connection, perform the connection after disconnecting the power
cord.
5. When the measurement is completed, the measurement results are
displayed. You can check each setting using the cursors </> LEFT/RIGHT.
Select "Save" and press ENTER to save the settings.
6. Disconnect the speaker setup microphone.
Comments
0 comments
Please sign in to leave a comment.