TX-8270-Network Settings
When LAN is configured with a DHCP, set "DHCP" to "Enable" to configure the setting automatically. Further, to assign fixed IP addresses to each component, you must set "DHCP" to "Disable" and assign an address to this unit in "IP Address" as well as set information related to your LAN, such as Subnet Mask and Gateway.
- Wi-Fi
- Connect the unit to network via wireless LAN router
- "On": Wireless LAN connection
- "Off (Wired) (default value)": To connect via wired LAN
- Wi-Fi Setup
- You can configure wireless LAN settings by pressing ENTER when "Start" is displayed
- Wi-Fi Status
- The information for the connected access point is displayed.
- "SSID": The SSID of the connected access point
- "Signal": The signal strength of the connected access point
- "Status": The status of the connected access point
- MAC Address
- This is the MAC address of the AV receiver.
- This value is specific to the component and cannot be changed.
- DHCP
- "Enable (default value)": Auto configuration by DHCP
- "Disable": Manual configuration without DHCP
- If "Disable" is selected, you must set "IP Address", "Subnet Mask", "Gateway", and "DNS Server" manually
- IP Address
- Displays/Sets the IP address
- Subnet Mask
- Displays/Sets the subnet mask
- Gateway
- Displays/Sets the gateway
- DNS Server
- Displays/Sets the primary DNS server
- Proxy URL
- Displays/Sets the proxy server URL
- Proxy Port
- Displays/Sets the proxy server port number when you enter "Proxy URL"
- Friendly Name
Change the device name for this unit which is shown on other devices connected to the network to an easily recognized name. This is set to Onkyo TX-8270 ****** at the time of purchase. (* stand for alphanumeric characters identifying each unit)
- Press ENTER to display the Edit screen
- Select a character or symbol with the cursors and press ENTER
Repeat it to input 31 or less characters.
"A/a": Switches between upper and lower cases. (Pressing CAPS on the remote controller also toggles between upper and lower cases.)
"<-" "->": Moves the cursor to the arrow direction: Removes a character on the left of the cursor
: Enters a space
Pressing CLR on the remote controller will remove all the input characters - After inputting, select "OK" with the cursors and press ENTER.
The input name will be saved
- AirPlay Password
You can set a password of up to 31 characters so that only registered users can use AirPlay.
- Press ENTER to display the Edit screen
- Select a character or symbol with the cursors and press ENTER
Repeat it to input 31 or less characters.
"A/a": Switches between upper and lower cases. (Pressing CAPS on the remote controller also toggles between upper and lower cases.)
"<-" "->": Moves the cursor to the arrow direction.: Removes a character on the left of the cursor.
: Enters a space.
To select whether to mask the password with "¢" or display it in plain text, press MENU on the remote control.
Pressing CLR on the remote controller will remove all the input characters. - After inputting, select "OK" with the cursors and press ENTER.
The input password will be saved.
- Usage Data
- As a means of improving the quality of our products and services, we may collect information about your usage over the network. Select "Yes" if you agree to our collecting this information. Select "No" if you do not want us to collect this information. (Default Value is "No") You can set this after confirming the Privacy Policy. When you select "Usage Data" and press ENTER, the Privacy Policy is displayed. (The same screen is displayed once also when setting up the network connection.)
If you agree to the collection of the information, this setting also becomes "Yes". Note that if you agree to the Privacy Policy but select "No" for this setting, the information will not be collected.
- As a means of improving the quality of our products and services, we may collect information about your usage over the network. Select "Yes" if you agree to our collecting this information. Select "No" if you do not want us to collect this information. (Default Value is "No") You can set this after confirming the Privacy Policy. When you select "Usage Data" and press ENTER, the Privacy Policy is displayed. (The same screen is displayed once also when setting up the network connection.)
- Network Check
- You can check the network connection.
Press ENTER when "Start" is displayed.
- You can check the network connection.
- Wait for a while if "Network" cannot be selected. It will appear when the network feature is started.
Comments
0 comments
Article is closed for comments.