1. Onkyo Product Support
  2. Home Theater Systems
  3. HT-S5910

Articles in this section

See more

HT-S5910 - Setup Menu - Speakers

Configuration

Speaker Channels

Default Value: 5.1.2 ch

Setting Details

Select "2.1 ch", "3.1 ch", "4.1 ch", "5.1 ch", "6.1 ch", "7.1 ch", "2.1.2 ch", "3.1.2 ch", "4.1.2 ch" or "5.1.2 ch" to suit the number of speaker channels connected.

 

Subwoofer

Default Value: Yes

Setting Details

Set whether a subwoofer is connected or not.

"Yes": When a subwoofer is connected
"No": When a subwoofer is not connected

 

Height Speaker

Default Value: Bundled Dolby Speaker

Setting Details

Set the speaker type if height speakers are connected to the SURROUND BACK or HEIGHT terminals.  Select "Bundled Dolby Speaker", "Front High", "Top Front", "Top Middle", "Top Rear", "Rear High",
"Dolby Speaker (Front)" or "Dolby Speaker (Surr)" according to the type and layout of the connected
speakers.

  • If the item cannot be selected even though connection is correct, check if the setting in "Speaker Channels" matches the number of connected channels

 

Zone B Speaker

Default Value: No

Setting Details

Set whether speakers are connected to Zone B speaker terminals.

"Yes": When speakers are connected to Zone B speaker terminals

"No": When speakers are not connected to Zone B speaker terminals

  • This setting is fixed to "No" if "Bi-Amp" is set to "Yes".
  • This setting cannot be selected when surround back speakers or height speakers are installed.

 

Zone B Output Level

Default Value: Fixed

Setting Details

Select whether to adjust the volume on the pre-main amplifier in the separate room or on this unit when outputting to Zone B.

"Fixed": Adjust on the pre-main amplifier in the separate room

"Variable": Adjust on this unit

  • This setting is fixed to "Variable" if "Zone B Speaker" is set to "Yes".
  • This setting is fixed to "Variable" if "Bi-Amp" is set to "Yes". 

 

Bi-Amp

Default Value: No

Setting Details

Set whether the front speakers are bi-amp connected.

"No": When front speakers are not bi-amp connected
"Yes": When front speakers are bi-amp connected

  • This setting is fixed to "No" if "Zone B Speaker" is set to "Yes".
  • This setting cannot be selected when surround back speakers or height speakers are installed.

 

Speaker Impedance

Default Value: 6 ohms or above

Setting Details

Set the impedance (Ω) of the connected speakers.

"4 ohms": When any of the connected speakers have 4 Ω or more to less than 6 Ω impedance.
"6 ohms or above": When the connected speakers all have 6 Ω or more impedance.

 

 

Crossover

Front

Default Value: 100Hz

Setting Details

Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel.

"Full Band": Full band will be output.

If "Configuration" - "Subwoofer" is set to "No", "Front" is fixed to "Full Band", and the low pitched range of the other channels is output from the front speakers. Refer to the instruction manual of your speakers to make the setting.

 

Center

Default Value:100Hz

Setting Details

 Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel.

"Full Band": Full band will be output.

  • "Full Band" can be selected only when "Front" is set to "Full Band".
  • If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels.

 

Height

Default Value: 100Hz

Setting Details

Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel.

"Full Band": Full band will be output.

  • "Full Band" can be selected only when "Front" is set to "Full Band".
  • If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels.

 

Surround

Default Value: 100Hz

Setting Details

Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel.

"Full Band": Full band will be output.

  • "Full Band" can be selected only when "Front" is set to "Full Band".
  • If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels.

 

Surround Back

Default Value: 100Hz

Setting Details

Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each
channel.

"Full Band": Full band will be output.

  • "Full Band" can be selected only when "Surround" is set to "Full Band".
  • If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels.

 

LPF of LFE

Default Value: 120Hz

Setting Details

Set the low-pass filter for LFE (low-frequency effect) signals in order to pass only the lower frequency signals than the set value, and thus cancel unwanted noises. The low-pass filter is effective only on sources with LFE channel.  The value from "80 Hz" to "120 Hz" can be set.
"Off": When this function is not used

 

Double Bass

Default Value: On

Setting Details

This can be selected only when "Configuration" - "Subwoofer" is set to "Yes" and "Front" is set to "Full Band".  Bass output is boosted by feeding bass sounds from the front right and left, and center speakers to the subwoofer.


"On": Bass output is boosted.

"Off": Bass output is not boosted.

  • This function is not automatically set even if AccuEQ Room Calibration is performed.

 

 

Distance

Front Left

Default Value: 12.0 ft

Setting Details

Specify the distance between each speaker and the listening position.

 

Center

Default Value:12.0 ft

Setting Details

Specify the distance between each speaker and the listening position.

 

Front Right

Default Value: 12.0 ft

Setting Details

Specify the distance between each speaker and the listening position.

 

Height Left

Default Value: 9.0 ft

Setting Details

Specify the distance between each speaker and the listening position.

 

Height Right

Default Value:9.0 ft

Setting Details

Specify the distance between each speaker and the listening position.

 

Surround Right

Default Value: 7.0 ft

Setting Details

Specify the distance between each speaker and the listening position.

 

Surr Back Right

Default Value: 7.0 ft

Setting Details

Specify the distance between each speaker and the listening position.

 

Surr Back Left

Default Value: 7.0 ft

Setting Details

Specify the distance between each speaker and the listening position.

 

Surround Left

Default Value: 7.0 ft

Setting Details

Specify the distance between each speaker and the listening position.

 

Subwoofer

Default Value: 12.0 ft

Setting Details

Specify the distance between each speaker and the listening position.

 

 

Level Calibration

Front Left

Default Value: 0 dB

Setting Details

Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.

 

Center

Default Value: 0 dB

Setting Details

Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.

 

Front Right

Default Value: 12.0 ft

Setting Details

Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.

 

Height Left

Default Value: 0 dB

Setting Details

Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.

 

Height Right

Default Value: 0 dB

Setting Details

Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.

 

Surround Right

Default Value: 0 dB

Setting Details

Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.

 

Surr Back Right

Default Value: 0 dB

Setting Details

Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.

 

Surr Back Left

Default Value: 0 dB

Setting Details

Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.

 

Surround Left

Default Value: 0 dB

Setting Details

Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.

 

 

Dolby Enabled Speaker

Surround Left

Default Value: 6.0 ft

Setting Details

Set the distance between the Dolby Enabled Speaker and the ceiling. Select between "0.1 ft/0.03 m" and "15.0 ft/4.50 m" (0.1 ft/0.03 m units).

  • The unit of distance (ft/m) is displayed using the unit selected for the "Distance" setting.

 

Surround Left

Default Value: Off

Setting Details

You can enhance the reflection effect of Dolby Enabled Speakers from the ceiling.

"Off": When this function is not used

"On": When this function is used

  • This setting can be selected when "Configuration" - "Height Speaker" is set to "Dolby Speaker".

 

Speaker Virtualizer

The Speaker Virtualizer function can be switched between On and Off.

Speaker Virtualizer

Default Value: On

Setting Details

"On": Listening modes such as T-D that have virtual speaker effects can be selected. 

"Off": Listening modes such as T-D that have virtual speaker effects cannot be selected.

Related articles

Comments

0 comments

Please sign in to leave a comment.