HT-S3910 - Setup Menu - Speaker
Change the settings of connection environment of the speakers.
Configuration
Speaker Channels
- Default Value: 5.1 Ch
- Setting Details
Select "2.1 ch", "3.1 ch", "4.1 ch", "5.1 ch", "2.1.2 ch" or "3.1.2 ch" to suit the number of speaker channels connected.
Subwoofer
- Default Value: Yes
- Setting Details
Set whether a subwoofer is connected or not.
"Yes": When a subwoofer is connected
"No": When a subwoofer is not connected
Height Speaker
- Default Value: Top Middle
- Setting Details
Set the speaker type if height speakers are connected to the SURROUND or HEIGHT terminals. Select "Top Middle", "Dolby Speaker (Front)" or "Front High" according to the type and layout of the
connected speakers.- If the item cannot be selected even though connection is correct, check if the setting in "Speaker Channels" matches the number of connected channels.
Speaker Impedance
- Default Value: 6 Ohms or above
- Setting Details
Set the impedance (Ω) of the connected speakers. "4 ohms": When any of the connected speakers
have 4 Ω or more to less than 6 Ω impedance "6 ohms or above": When the connected speakers all have 6 Ω or more impedance.
Crossover
Front
- Default Value: 150 Hz
- Setting Details
Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel.
"Full Band": Full band will be output. - If "Configuration" - "Subwoofer" is set to "No", "Front" is fixed to "Full Band", and the low pitched range of the other channels is output from the front speakers.
Center
- Default Value: 150 Hz
- Setting Details
Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel.
"Full Band": Full band will be output.
- "Full Band" can be selected only when "Front" is set to "Full Band".
- If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels.
Height
- Default Value: 150 Hz
- Setting Details
Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel.
"Full Band": Full band will be output.
- "Full Band" can be selected only when "Front" is set to "Full Band".
- If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels.
Surround
- Default Value: 150 Hz
- Setting Details
Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
- "Full Band" can be selected only when "Front" is set to "Full Band".
- If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels.
LPF of LFE
- Default Value: 120 Hz
- Setting Details
Set the low-pass filter for LFE (low-frequency effect) signals in order to pass only the lower frequency signals than the set value, and thus cancel unwanted noises. The low-pass filter is effective only on sources with LFE channel.
The value from "80 Hz" to "120 Hz" can be set.
"Off": When this function is not used.
Double Bass
- Default Value: On
- Setting Details
This can be selected only when "Configuration" - "Subwoofer" is set to "Yes" and "Front" is set to "Full Band".
Bass output is boosted by feeding bass sounds from the front right and left, and center speakers to the subwoofer.
"On": Bass output is boosted.
"Off": Bass output is not boosted.
Distance
Front Left
- Default Value: 12.0 ft/3.60 m
- Setting Details
Specify the distance between each speaker and the listening position.
Center
- Default Value:12.0 ft/3.60 m
- Setting Details
Specify the distance between each speaker and the listening position.
Front Right
- Default Value:12.0 ft/3.60 m
- Setting Details
Specify the distance between each speaker and the listening position.
Height Left
- Default Value: 12.0 ft/3.60 m
- Setting Details
Specify the distance between each speaker and the listening position.
Height Right
- Default Value: 12.0 ft/3.60 m
- Setting Details
Specify the distance between each speaker and the listening position.
Surround Right
- Default Value: 7.0 ft/2.10 m
- Setting Details
Specify the distance between each speaker and the listening position.
Surround Left
- Default Value: 7.0 ft/2.10 m
- Setting Details
Specify the distance between each speaker and the listening position.
Subwoofer
- Default Value: 12.0 ft/3.60 m
- Setting Details
Specify the distance between each speaker and the listening position. - Default values vary depending on the regions.
- The unit of distance can be changed by pressing the MODE button on the remote controller. When using the unit "feet", the setting is available in increments of 0.1 ft from 0.1 ft to 30.0 ft. When using the unit "meter", the setting is available in increments of 0.03 m from 0.03 m to 9.00 m.
Level Calibration
Front Left
- Default Value: 0 dB
- Setting Details
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.
Center
- Default Value: 0 dB
- Setting Details
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.
Front Right
- Default Value: 0 dB
- Setting Details
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.
Height Left
- Default Value: 0 dB
- Setting Details
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.
Height Right
- Default Value: 0 dB
- Setting Details
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.
Surround Right
- Default Value: 0 dB
- Setting Details
Surround Left
- Default Value: 0 dB
- Setting Details
Select a value between "-12 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.
Subwoofer
- Default Value: 0 dB
- Setting Details
Select a value between "-15 dB" and "+12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level.
Dolby Enabled Speaker
Dolby Enabled Speaker to Ceiling
- Default Value: 6.0 ft/1.80 m
- Setting Details
Set the distance between the Dolby Enabled Speaker and the ceiling. Select between "0.1 ft/0.03 m" and "15.0 ft/4.50 m" (0.1 ft/0.03 m units).- The unit of distance (ft/m) is displayed using the unit selected for the "Distance" setting.
AccuReflex
- Default Value: Off
- Setting Details
You can enhance the reflection effect of Dolby Enabled Speakers from the ceiling.
"Off": When this function is not used
"On": When this function is used - This setting can be selected when "Configuration" - "Height Speaker" is set to "Dolby Speaker".
Speaker Virtualizer
The Speaker Virtualizer function can be switched between On and Off.
Speaker Virtualizer
- Default Value: On
- Setting Details
"On": Listening modes such as T-D that have virtual speaker effects can be selected.
"Off": Listening modes such as T-D that have virtual speaker effects cannot be selected.
Comments
0 comments
Please sign in to leave a comment.